This submit about how to make 3 Easy Do-it-yourself Floating Picture Frames And How to Cut Plexiglass is sponsored by The Household Depot as portion of the #THDProSpective Method. It also contains affiliate inbound links. See policies.
Quick Do it yourself image frames are truly a single of my most requested tutorials and oddly adequate, until now, I didn&rsquot have quite a few to share!
.
I essentially developed my dad a large Diy personalized photo frame as a Christmas present a few several years ago and shared the tutorial for it right here. But it employed dowels, and a router, and it might have been a small a lot more concerned than most people are seeking for.
So, in this article, I&rsquom likely to display you how I made 3 unique style Tremendous Easy Do it yourself floating image frames with just two simple equipment. I&rsquoll also exhibit you how effortless it is to reduce plexiglass for them, also!
.
So if you&rsquore completely ready to get constructing, let&rsquos go! I&rsquove bought the movie tutorial in this article and the stage by move under:
Instruments AND Materials:
- Miter observed (or any wooden chopping noticed is great&ndashdoesn&rsquot have to be a MITER saw)
- Nail Gun (optional, just will make things more rapidly)
- Wood Glue
- ¾&Prime square dowels
- 1×2 boards
- ¼&Primary x 1 ⅛&Prime lattice trim
- Slender Plexiglass Sheets
- Ryobi A single+ HP Minimize Off Resource (utilized to minimize plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in position of clamps to maintain items though wooden glue dries)
- Change buttons
A Note About FLOATING Image Frames:
I&rsquom sharing how to make 3 various model FLOATING photo frames in this tutorial, but the initial step to making any of them is cutting the plexiglass to the measurement you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this action. But because the graphics/photographs I framed are &ldquofloating&rdquo within the body, they&rsquore mainly sandwiched in between two parts of plexiglass. So plexiglass/acrylic is essential to be in a position to &ldquofloat&rdquo your image.
.
To make points uncomplicated to modify out in these frames, I also utilized these switch buttons&mdashor I simply call them twisty tabs&ndashon the back again to maintain the plexiglass in position.  
HOW TO Minimize PLEXIGLASS
Generally, I have my area glass shop minimize my glass and plexiglass parts for my assignments.  But due to the fact these plexiglass pieces will be modest and numerous custom dimensions, it would be a great deal cheaper, a lot quicker and simpler to just slash them myself.
.
I utilised some (about) ⅛&rdquo acrylic sheets from Dwelling Depot.  They appear in a variety of sizes, all the way up to a 4×8 sheet.  I just grabbed some 11x14s.
I developed some straightforward graphics on my computer system (PicMonkey and Canva are terrific for this!) and also utilized a patch that I received a couple of several years ago at a convention for these frames.  You can use a photo, a poster, cloth, no matter what you want to frame for this.
.
I laid them out on my sheet how I favored the spacing, then marked the place I wanted to slash&ndashno measurements listed here&hellipjust eyeballing how I imagined the spacing all over the image looked great.
Now, I&rsquove made use of the low-cost minor hand knife they assert will slice plexiglass before and it was a horrible experience with pretty very poor results.  I&rsquove also employed a jig saw to slice plexiglass and it melts, receives caught, then chips or cracks the sheet.
.
So THIS time, I experimented with this new Ryobi A person+ HP Compact Slash Off Tool with a plastic slicing blade and was completely impressed with how swift and clean up the cuts ended up.
When I 1st noticed this device, I uncovered it sort of strange looking.  But soon after I utilized it, I comprehended the concept. 
.
It&rsquos basically a hybrid involving a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety levels. 
.
It&rsquos compact and lightweight and it&rsquos got a forward and reverse swap to switch the blade both equally instructions.  It&rsquos also bought a variable pace cause&mdashwhich is superior for cutting plastic to support protect against melting. 
It arrives with a plastic and drywall blade, a metallic minimize off wheel, and a diamond blade for chopping tile and cement board.  You can discover more about the new Ryboi Just one+ HP lower off resource at the connection listed here if you&rsquore interested.
.
For chopping straight lines on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the steel blade guard in opposition to it to make the cut.  You can skip the straight edge and freehand these cuts, much too if you have a continual hand. (I don&rsquot haha!)
I did obtain it reduce most effective in this scenario with the change in reverse. It seemed to not melt that way.
.
I slice two parts similar in size for each and every merchandise I was framing. Then, I was ready to get started creating the genuine floating photograph frames.
Easy Do-it-yourself FLOATING Picture Body Type one
Model 1 is my individual favorite, so I&rsquoll start off with it 😊
This distinct floating image frame structure requires ¾&Prime sq. dowels and 1×2 board. It is in essence just a one×2 wrapped close to a sq. dowel body.
.
I employed ¾&rdquo square dowels for this and set up my miter saw to cut forty five degrees.  Now, you don&rsquot have to miter these.  You can depart it on 90 and make butt joints.  You also don&rsquot have to have a MITER saw for this.  Any noticed that you can reduce reasonably straight with will get the job done fantastic.
.
I essentially trimmed 4 items of sq. dowel so that when in shape collectively, they&rsquod be just hardly (like ⅛&Prime) even bigger than the plexiglass piece I was placing in it.
I applied wood glue to the corners and nailed them collectively with brad nails.  If you are client, and don&rsquot have a nail gun, only glue and clamp right until dry.
.
Immediately after the glue had dried, I reduce to healthy one×2 items with forty five diploma mitered corners all around this body.  Once again, butt joints are fine listed here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s close to the edges leaving about ¼&rdquo sticking out the back again aspect of the plexiglass, so that when I set up the two ⅛&Key plexiglass items, it&rsquoll be flush across the back again facet of the frame.
Then, I screwed these twisty tabs into the again sides of the frame to hold the plexiglass in place.  I&rsquoll go back again and clear the sawdust off the plexiglass afterwards, but for now, I set this off to the aspect to make the following frame.
Uncomplicated Diy FLOATING Image FRAMES Type two
Style 2 is a little easier and is created of 1x2s and ¼&rdquo thick by one ⅛&Key huge lattice trim.
I commenced by reducing down the lattice parts so it would make a body that the plexiglass would in shape Inside of.  Once more, just like prior to, the mitered corners are optional.
As soon as I experienced this lattice frame cut, I measured its overall dimension and slash 1×2 pieces to make a frame whose over-all dimensions matched that of the lattice frame. See under 1×2 frame laying on prime of lattice body&ndashthey&rsquore the same size.
I glued and nailed the 1×2 body alongside one another and clamped right up until dry. Once more, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice body on to the back.  navigate to this web-site utilized a hefty object to keep it in spot right until it was dry, then, I screwed twisty tabs on the back to hold the plexiglass in spot. 
Considering that the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass items are placed inside, almost everything ought to sit flush across the back again just like the very last frame.
Again, I&rsquoll go back again and thoroughly clean the sawdust off later on, but for now, I moved on to the past design body.
Quick Do-it-yourself FLOATING Image Frame Design 3
Type three is the exact same concept as style 1, but rather of making use of 1x2s, I utilized ¼&Primary x 1 ⅛&Primary lattice trim to keep the body a minor thinner and far more minimalist on the lookout.
So, I reduce ¾&rdquo square dowels to make a frame the identical size or slightly larger than the plexiglass I was framing and glued and nailed it together.
Then, I slice lattice trim to wrap all-around that frame. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back again facet of the square dowel frame so that when the two pieces of ⅛&rdquo plexiglass are mounted, it&rsquoll all be flush across the again.
.
I didn&rsquot have any brad nails small more than enough to nail this body on, so I merely glued and clamped till it was dry.
If you don&rsquot have clamps, you can use painters tape to form of wrap about the pieces to maintain until the glue dries OR just use some tremendous glue or CA glue to assist hold items in position till the true wooden glue is cured.
.
Then, just like the final two frames, I mounted twisty tabs to maintain the plexiglass in put.
FLOATING Image Frame HANGING Options
The last phase is clear up and hanging.  I utilised some glass cleaner to clean up all the saw dust, then utilized a piece of double sided tape on the again plexiglass piece to make sure the images stay in place, then place the frames back jointly.
.
To hold, you can use your standard sawtooth hangers for this.
Or simply just spot it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and cling it on a piece of wood dowel you screwed into the wall.
As you can see, creating image frames doesn&rsquot have to be complex.  This is a good rookie task you can tackle with small equipment and get as innovative as you want. 
.
I truly hung these graphics up in my desk region to assistance keep me determined whilst functioning by yourself from dwelling appropriate now. So, now that my desk area is comprehensive, I guess I really should likely get again to perform 😊
I hope you&rsquove loved this tiny project.  There are a lot a lot more coming your way, so be sure to subscribe to my e-newsletter underneath so you don&rsquot overlook out on what&rsquos coming next!
.
And don&rsquot forget to pin this for later!
Until finally following time, delighted creating 😊